How to Replace the Blades in a Nemco Easy Chopper [Video]

When using a Nemco Easy Chopper, sharp blades mean the difference between getting clean, quick cuts and smashing your food to pulp. The most cost-saving option here is to replace the individual blades in the cutting assembly once they begin to dull.

Find your replacement parts here!

 

Before taking action from the content or resources published here, we request that you visit and review our terms of use.

 

Video Transcript:

I’m Chris Tavano for Tundra Restaurant Supply. In today’s episode I’m going to show you how to change the blades and blade assembly to your Nemco Easy Chopper II.

The first thing you’re going to want to do is remove your pusher block and your base assembly base. Two little bushings just slide right off the greased poles and your blade assembly should slide right off as is. First and foremost this is your blade assembly faced up. Be very careful as these blades facing up are very, very sharp. I’m going to want to turn it upside down exposing the bolts. Get your crescent wrench and we’re going to loosen these all the way off. Once you’ve unscrewed your bolts the base plate should come right off. Set that aside and now you’ve exposed the bottom side of your blades.

This is going to be how we’re going to replace these. These metal bars, those are going to stay. Do not throw those away.  An easy way to get rid of your blades, flip it upside down, give it a little tap. Your entire blade assembly comes out. The first thing you’re going to want to note when you open your package of new blades is that there are two different kinds. Some are going to be loaded first and some are going to be loaded second. The best way to tell is identify where the slit is on the blade.

If you notice both these blades are facing the sharp edge towards you and this front row has slits towards the back base of that blade. Whereas the second one has the slits going through the cutting edge of that blade. We’re going to want to put in these ones first where you see the slit coming from the back. From here you’re going to want to organize your spacer guides. If you notice these little bars that we kept from the original, there’s little slits.

You’re going to want to see the slit that goes all the way through the wall of that guide to be facing the inside of the assembly. Place all four of those around the perimeter of the assembly itself and from there we can get our first set of blades where there is no slit on the cutting edge itself. Being very careful with these blades, you’re going to put blade down in the first slit horizontally in your spacer guide and the next one. Being sure to be very careful putting the cutting edge of each blade down into the spacer guide slits.

So after you’ve got your first set down we’ll work on the second set of blades where the slit goes through the actual beveled cutting edge itself. And these blades we’re going to place perpendicular going through each and every slit on the previous blades that we set in, as well as the spacer guide itself. Be sure that you’re pushing down with enough pressure on these blades to where all the tops are even and flush. Don’t have to worry too much on this side because remember you’re putting the cutting edge of the blade down into your table. These edges are not sharp.

As we put our base plate back onto our blade assembly, be sure to line up the post holes accordingly on your base. Screw your nuts back in, righty-tighty. Now remember when you flip this over you’re going to have brand new sharp blades so do not touch that surface up there. Once you’re replaced the blades on your blade assembly, it’s just a matter of getting this block back on the base of your chopper stand. Keep in mind that these top blades are very sharp to the touch and these elongated holes are for your post slots.

You’re going to grab your bushings next; slide those on. If this is getting a little stuck just add a little bit more food grade lubricant or grease to these posts. Then you’ve got your pusher block back on. That’s how you replace the blades in a blade assembly for your Nemco Easy Chopper II. Here’s to a better mise en place!

About Nathan Combs

By day: Videographer for Tundra Restaurant Supply. By different time of day: Hiking, biking, skiing and hammock enthusiast. And by night... do whatever I want. No job.

Check Also

How to Cut an Acorn Squash

Find out the right way to cut an acorn squash with our own Chris Tavano.

Leave a Reply

Your email address will not be published. Required fields are marked *